@article { author = {MESBAHZADEH, TAYYEBEH and Ayazi, Zahra and soleimani sardoo, farshad}, title = {Evaluation of morphoscopy and granolometry of wind sediments (Case study Aran-Kashan}, journal = {Journal of Range and Watershed Managment}, volume = {71}, number = {3}, pages = {787-795}, year = {2018}, publisher = {University of Tehran}, issn = {5044-2008}, eissn = {2423-7795}, doi = {10.22059/jrwm.2018.251307.1226}, abstract = {By identifying the removal areas the reasons can be identified instead of addressing the causes, And focused on executive activities in the harvesting areas And for this, the identification of sediments is particular importance In this paper, with the aim of better understanding and interpreting sedimentary samples, Investigating and analyzing the distribution of sediments in the facies of the study area has been investigated. For this purpose, after sampling of surface soil and preparation of samples, The drying procedure was performed according to A.S.T.M standard in 8 classes, which was smaller than 64 microns to 4000 microns. By entering the data into Gradistat software, statistical parameters such as mid-diameter, skewness and sample sorting were calculated based on the Fulc's comprehensive drawing method. The results of the study showed that the particle sorting is between 0.8 and 0.3, which confirms the near-average spacing distance from the harvesting area to the sediment accumulation point. The results of the particle tilting index are in the median vein facies, agricultural lands, agriculture, and sandy areas with symmetrical pebble cover. In other facies, the index is tilted towards fine particles. In the facies of the Rigi plain, the puffy lands and the permafrost shells of the wear coefficient classes are between 0-200 and then fully angled and the particles are transported from a distance. In the rest of the facies, the wear coefficients are between 200 to 400, in which case the particles are semi-angled and the particles are transported from a relatively distant distance.}, keywords = {Grain,Morphoscopy,sorting,Bending,Abrasion coefficient,Gradistat}, title_fa = {ارزیابی مورفوسکوپی و دانه‌بندی رسوبات بادی (مطالعۀ موردی آران – کاشان‌)}, abstract_fa = {شناخت مناطق برداشت رسوبات بادی از اصول اولیۀ کنترل و مبارزه با فرسایش بادی محسوب می‌شود. زیرا با شناسایی‌مناطق برداشت می‌توان به جای معلول، علل را شناسایی کرد و فعالیت‏های اجرایی را در مناطق برداشت متمرکز کرد، و برای این کار شناخت رسوبات حائز اهمیت خاص است. در این مقاله باهدف شناخت هرچه بهتر و تفسیر نمونه‌های رسوبی، به بررسی و تحلیل توزیع رسوبات در رخساره‌های منطقۀ مورد مطالعه پرداخته شده است. بدین منظور پس از نمونه‌برداری از خاک سطحی و آماده‌سازی نمونه‌ها، عملیات دانه‌بندی به روش الک خشک و بر اساس استاندارد A.S.T.M  در8 طبقه شامل کوچک‌تر از 64 میکرون تا بزرگ‌تر از 4000 میکرون انجام شد. با ورود داده‌ها به نرم افزار Gradistat پارامترهای آماری همانند قطر میانه، چولگی و جورشدگی نمونه‏ها بر اساس روش جامع ترسیمی فولک محاسبه گردید. نتایج تحقیق نشان داد جورشدگی ذرات بین 8/0 – 3/0 که به نوعی تأییدکنندۀ فاصلۀ حمل نزدیک تا متوسط ذرات از منطقۀ برداشت خود تا محل تجمع رسوبات می‌باشد. نتایج حاصل  از شاخص کج شدگی ذرات در رخساره‎های رگ متوسط‌دانه، اراضی کشاورزی-رسی، کشاورزی و پهنه‌های ماسه‌ایی با پوشش سنگریزه‏ایی متقارن می‌باشد. در بقیۀ رخساره­ها شاخص کج‌شدگی به سمت ذرات ریزدانه می‎باشد. در رخساره‏های دشت ریگی، اراضی پفی و پوسته‎های شلجمی طبقات ضریب سایش بین200-0 می­باشد، در این­صورت کاملاً زاویه‌دار می­باشد و ذرات از فاصله‌ای نزدیک حمل شده است. در بقیۀ رخساره‏ها طبقات ضریب سایش بین400 - 200 قرار گرفته که در این­صورت ذرات نیمه زاویه­دار بوده و ذرات از فاصله‌ای نسبتاً نزدیک حمل شده است.}, keywords_fa = {Grain,Morphoscopy,sorting,Bending,Abrasion coefficient,Gradistat}, url = {https://jrwm.ut.ac.ir/article_68891.html}, eprint = {https://jrwm.ut.ac.ir/article_68891_5cf22b5cbb0ea27af48e4fe4e9093b2b.pdf} }